Changing the functions of this thing is something which you need to do with extreme caution. If not, you can damage the radio as well and you cannot get a replacement for that. This is why it is important that for you to familiarize with the process and stick with it even if you have always wanted to explore.
Painting this product is not allowed at all. Thus, just let your military CB antenna be and gain the approval of the officer in charge. You have no time to waste especially if you are going to be deployed in another mission in the next twenty four hours. Tardiness is not allowed in your line of work.
Do not tighten the set up that much. Yes, it is perfectly understandable that you are worried about the position of this thing but you can always have fasteners to complete the set up. That would prevent the base from cracking up and leading you to buy a new one. Also, use a torque wrench in this task for your safety.
Open the bottom part with the use of common tools. However, never use a knife since that can make the lid open more which can pave way to air. If you have a screwdriver, that shall be enough and the next thing that you need to focus on is the location of the main cable. Read the label for you not to have mistakes.
Turn the fifth capacitor slowly with the use of your tools. Make sure that it is the correct nub buy moving clockwise from the cable. Also, know the power capacity of the antenna for you to match things up. Excessively turning the capacitor would only dull other frequencies and even lead your radio to blow up.
Lengthen the cable for as long as you can. You simply do not have the luxury of time to make another purchase again. Moreover, always wear gloves even when you are just cutting the cable. This can keep you from being electrocuted and getting burned once you get to the fitting stage of the procedure.
Close the gaps between all of the things which you are trying to connect. Also, separate metals away from each other. Your reception must be free from any distractions and that can never in the presence of a metal to metal contact. You can lose all signal in an instant and that is not going to help you in case of an emergency.
Use a SWR meter to see if you got the measurements right. If there has been a mistake, be very patient in starting all over again. Buy the same set of materials and know where you got it wrong this time around.
Tightly close the lid after the test. Check it once again since a simple wave of air can destroy all of your efforts. So, put additional materials such as a tape for you to be sure that your antenna will be up and running.
Painting this product is not allowed at all. Thus, just let your military CB antenna be and gain the approval of the officer in charge. You have no time to waste especially if you are going to be deployed in another mission in the next twenty four hours. Tardiness is not allowed in your line of work.
Do not tighten the set up that much. Yes, it is perfectly understandable that you are worried about the position of this thing but you can always have fasteners to complete the set up. That would prevent the base from cracking up and leading you to buy a new one. Also, use a torque wrench in this task for your safety.
Open the bottom part with the use of common tools. However, never use a knife since that can make the lid open more which can pave way to air. If you have a screwdriver, that shall be enough and the next thing that you need to focus on is the location of the main cable. Read the label for you not to have mistakes.
Turn the fifth capacitor slowly with the use of your tools. Make sure that it is the correct nub buy moving clockwise from the cable. Also, know the power capacity of the antenna for you to match things up. Excessively turning the capacitor would only dull other frequencies and even lead your radio to blow up.
Lengthen the cable for as long as you can. You simply do not have the luxury of time to make another purchase again. Moreover, always wear gloves even when you are just cutting the cable. This can keep you from being electrocuted and getting burned once you get to the fitting stage of the procedure.
Close the gaps between all of the things which you are trying to connect. Also, separate metals away from each other. Your reception must be free from any distractions and that can never in the presence of a metal to metal contact. You can lose all signal in an instant and that is not going to help you in case of an emergency.
Use a SWR meter to see if you got the measurements right. If there has been a mistake, be very patient in starting all over again. Buy the same set of materials and know where you got it wrong this time around.
Tightly close the lid after the test. Check it once again since a simple wave of air can destroy all of your efforts. So, put additional materials such as a tape for you to be sure that your antenna will be up and running.
About the Author:
You can visit www.hascall-denke.com for more helpful information about Modifying A Military CB Antenna.
No comments:
Post a Comment